Get Answers from our
Community of Computer Experts

Register

How do i get netgear in the expander's actions does not fit the security key


Asked by
Keijo Ahola
2017/09/14 07:00
0 Like It
The downside is the question of the lifetime of the system is not good enough for netgear expanding security key has not tried many times what change the protection key does not understand.
Operating System:
Windows 8.1
Answer this question
best answer

 
2017/09/14 07:16
Hi Keijo,

Thank you for asking.

For your questions and concerned to be addressed properly. We recommend contacting NETGEAR directly by going to the link given below:

https://www.netgear.com/support/default.aspx

I hope this helps.

Regards,


Ryan


Cancel
 
Answered by
Lokesh Yadav
2017/11/05 13:01

0 votes

0
0
Hi Keijo,

Please use the below steps to resolve the issue. If you have a NETGEAR WiFi Extender with an Ethernet port (EX6100, for example):
  1. Use a computer to connect to NETGEAR WiFi Extender via Ethernet cable.
  2. Login to the web user interface of your NETGEAR WiFi Extender using http://myWiFiext.net.
    You will be prompted to enter a username and password.
    Default login credentials are:
    • Username: admin
    • Password: password
      Note: Username and password are case sensitive.
  3. Once you have successfully logged in, go to Setup > Wireless Settings.
  4. Check the value in the Password (Network Key) field under Security Options.
    If the password is not same as your Access Point (AP) password, change it so it matches your Access Point password.
  5. Click Apply. (Extender and AP password need to match)
  6. Reconnect your Wi-Fi devices to the NETGEAR WiFi Extender using either the WPS button or manual connection.

If you have a NETGEAR WiFi Extender without an Ethernet port (WN1000RP, for example):
  1. Reset your NETGEAR WiFi Extender back to factory default settings.
    To do this, press and hold the Factory Settings button on the side panel for 7 seconds.
  2. Connect via Wi-Fi to your NETGEAR WiFi extender
  3. Login to the web user interface of your NETGEAR WiFi Extender using http://myWiFiext.net.
    You will be prompted to enter a username and password.
    Default login credentials are:
    • Username: admin
    • Password: password
    Note: Username and password are case sensitive.
  4. Walk through the setup wizard to setup your connection to your Access Point. (Do not use WPS when reconnecting to the Access Point)
  5. Reconnect your Wi-Fi devices to your NETGEAR WiFi Extender using either the WPS button or manual connection.
Regards,
Lokesh
Cancel
Cancel

Welcome to Reviversoft Answers
ReviverSoft Answers is a place to ask any question you have about your computer and have it answered by the expert community.
Post your question
Ask your question to the community now
Similar questions
When I connect an external microphone to the jack, it is not working. I can see it in the "Sound" tab, but the levels is very low. I have tried with several microphones.
VIEW ANSWERS
6
Show full question
mein pc ist put mochte nun reviversoft auf mein laptop registriren wie geht das und was muß ich tun
VIEW ANSWERS
2
Show full question
I kept getting the blue screen with Driver Power State Failure error message and then my computer would restart. I found your product and it did not happen any more. I just purchased an anti-virus (kaspersky) and now it is doing it again. It is so frustrating. My computer is only 6 months old. It is a Asus desktop.
VIEW ANSWERS
2
Show full question
© 2017 Corel Corporation or its subsidiaries. All rights reserved. ReviverSoft is now part of Corel Corporation.
follow us